Below are part numbers from my BMW Tool Inventory file. All items are new. As I am able to locate the stock of these tools, I will photograph and price them at the bottom of this page.
88886000200 |
Engine brace/support for subframe removal (pick-up only) |
88886005010 |
Puller- Output seal removal tool |
88886005500 |
Handle for drift |
88886005550 |
Drift for steering spindle-E21/E30/E28/E23/E24 |
88886007500 |
Kukko Puller Kit for E30 Control Arm Tool |
88886111260 |
Drift for rear main seal (use with 005500 handle) |
88886111270 |
Installer for front timing cover seal-M10/M30 |
88886112300 |
Flywheel lock tool (use with 113240)-M42/M50 |
88886113050 |
Drift/installer for engine rocker shafts-M10/M20/M30 |
88886113060 |
Puller/extractor for M30 rocker shafts |
88886113070 |
Valve adjuster eccentric tool |
88886113100 |
Timing chain turning tool-all with double row chains |
88886113110 |
Timing chain turning tool-all with single row chains |
88886114030 |
Oil pressure test adapter - all exc M42 |
88886115010 |
Timing belt detensioner for M20 water pump removal |
88886231240 |
Installer-trans selector shaft seal (most std models)(with seals) |
88886231370 |
Installer - output shaft seal (e28 & most models) (long) |
88886231380 |
Installer - output shaft seal (e30) (short) |
88886251100 |
Pin wrench for shift lever bushing-E30/E28 (86-) |
88886312100 |
Puller-Frt wheel bearings & rear diff flange-3/5/7/8 |
| 88886312110 | Wheel Bearing Installation Tool - E36/E28/E34/E32 (all with 46mm hub nut) (D) |
88886312130 |
Press arbor/sleeve set-control arm bushings-E30/E36 |
88886312151 |
Control arm bracket tool-removal plate-E30/E36 |
88886312152 |
Control arm bracket tool-installer-E30/E36 |
88886312153 |
Control arm bracket tool-frame-E30/E36 |
88886312154 |
Control arm bracket tool-threaded rods-E30/E36 |
88886313112 |
Strut extension sleeve-E34/E30 front (12x1.5)(short) |
88886313114 |
Strut extension sleeve-E34/E30 rear (10x1.0) |
88886313115 |
Strut extension sleeve-E34/E30/E28 frt (12x1.5)(long) |
88886313170 |
Shock special tool-22mm deep socket |
88886322040 |
Ball joint press-tie rods & idler arm-E28/E24/E34 |
88886331300 |
Rilex Bearing puller-differential (All) (301>312) |
88886333120 |
Subframe Bushing Tool-E36/E32/E34 (3pc cap kit-R&R) |
88886334050 |
Drift for rear axle locking plate-E30/E28 |
88886334060 |
Drift for rear axle locking plate-E32/E34/E28/E23/E24 |
88886344000 |
Handbrake spring removal tool (also ABS transmitter) |
88886511040 |
Pin wrench-Bumper adjuster screw - E34 |
88886511110 |
Rain gutter removal tool-E32/E34/E38 |
88886512070 |
Pin wrench for door lock fastening nut-E32/E34/E36 |
88886513050 |
Windshield molding installation tool set |
88886513160 |
Bumper Rubber Tool-E21/E30, E28/E24/E23 |
88886520050 |
Crimping tool-for securing clips to seatcovers |
88886611250 |
Pliers for relay removal from fusebox |
90886311430 |
Ball Joint Separator-E36 (C) |
90886311440 |
Ball Joint Installation Tool-E36 (B) |
90886513190 |
Puller |
90886611150 |
Terminal connector tool kit |
B. E36 (3 series) Ball Joint Replacement Tool Set - this is the factory BMW ball joint removal and installation tool that allows you to safely replace the ball joints on 3 Series cars (92-98 318i/325i/328i/318ti). Retail price for this tool, assuming the dealer will sell it to you, is approx $550.00. (ball joint not included).......... $395.00
C. E36 (3 series) Ball Joint Separator - BMW factory tool used replacing control arms or thrust arms..... $50.00
D. 3/5/7 Series Front Wheel Bearing Installation Tool - BMW factory tool # 312110 for models with 46mm hub nut..... $245.00