(92811047501) - Fuel Rail/Pump Cap Nut - 911/964/993 (78-97), 928 (78-85), 944 (82-91), 924S (86-88), 968 (92-95) (Genuine Porsche) (1 available)

0 Lbs
 In stock
$10.99 $7.50

Description:

Porsche part number 92811047501 (formatted 928-110-475-01) is a genuine Porsche fuel pump and fuel rail domed cap nut (M12x1.5). It has been superseded by the updated OEM part number 92811047505. It seals the fuel pressure test port on the fuel injection rail or secures the check valve assembly on the fuel pump. Because it sits directly on pressurized fuel lines—and often above a hot engine—any failure or looseness creates a serious fuel leak and fire hazard. Alternate numbers for this part include 92811047500, 92811047501, 92811047503, 92811047504, 9281104750Y, and current number 92811047505.

  • Porsche 911 / 964 / 993. 1978–1997 (including Turbo, RS, and GT2 variants).
  • Porsche 928. 1978–1995 (Base, S, S4, GT, and GTS).
  • Porsche 944. 1982–1991 (Base, S, S2, and Turbo).
  • Porsche 924S. 1986–1988.
  • Porsche 968. 1992–1995. 

 

  • Seals the Fuel Rail Test Port (924S, 928, 944, 968, and Motronic 911s). It threads onto the end of the fuel injection rail to cap off the diagnostic port where mechanics attach a fuel pressure gauge. Inside the port sits a small steel ball bearing; tightening the domed cap nut presses that ball against its seat to keep pressurized fuel from escaping. 
  • Secures the Fuel Pump Check Valve (CIS 911 / 930 & Fuel Pumps). It threads onto the outlet fitting of the fuel pump to hold the banjo fitting and internal check valve tightly in place. 

 

Why You Need to Replace It - Because it is a solid metal nut, it does not wear out on its own during normal driving, so you usually only need to replace it in a few specific situations:

  • Rounded Hex Flats. Because the nut is tucked into tight spaces near the firewall or under the car by the fuel pump, using an open-end wrench often rounds off the soft outer edges. Once stripped, you cannot torque it down enough to seal properly.
  • Damaged or Cross-Threaded Internal Threads. Over-tightening or cross-threading the M12 threads prevents the nut from seating squarely, causing fuel to seep past the threads under pressure.
  • Upgrading a Fuel Pump. On older cars like the late-1970s 911, original fuel pumps often used a smaller 10 mm outlet fitting. Modern replacement pumps and check valves frequently upgrade to a 12 mm thread, requiring this larger 12 mm cap nut.
  • Missing Hardware After Diagnostics. If a previous mechanic removed the cap to test fuel pressure and forgot to reinstall it—or lost it—you must replace it before driving.
  • Severe Corrosion. Fuel pumps mounted underneath the front suspension or near the rear wheel well are exposed to road salt and moisture, which can rust the cap nut to the check valve. 

Viewed Products

  In stock
$76.75 $46.05
Porsche part number 95135291910 (formatted 951-352-919-10) is a genuine Porsche 28 mm...
  In stock
$227.13 $159.00
Porsche part number 93035608104 (formatted 930-356-081-04) is a genuine Porsche fuel...
  In stock
$258.66 $181.10
Porsche part number 93035606201 (formatted 930-356-062-01) is a genuine Porsche fuel...